Installing a Blink Doorbell with a wedge improves camera angle and motion detection. This guide walks you through every step—from tools to final setup—for a secure, professional-looking installation.
Key Takeaways
- Use the right tools: A drill, level, screwdriver, and measuring tape ensure a clean, secure mount.
- Choose the best location: Install at 4–5 feet high, facing the walkway, with a clear view of visitors.
- Wedge improves angle: The wedge helps tilt the doorbell downward for better coverage and fewer blind spots.
- Test before final mount: Use Blink’s app to check the camera view before tightening screws.
- Secure wiring safely: If replacing an old doorbell, cap wires properly to avoid electrical hazards.
- Sync with the app: Complete setup in the Blink app for live view, alerts, and recordings.
- Troubleshoot common issues: Fix Wi-Fi, battery, or motion detection problems with simple fixes.
How to Install Blink Doorbell with Wedge
Installing a Blink Doorbell with a wedge isn’t just about mounting a device—it’s about improving your home’s security with better camera angles, clearer views, and smarter motion detection. Whether you’re replacing an old doorbell or setting up a new one, using the included wedge can make a big difference in how well your Blink Doorbell captures visitors, packages, and unexpected activity.
In this guide, you’ll learn everything you need to know to install your Blink Doorbell with a wedge the right way. We’ll cover the tools you’ll need, how to choose the perfect spot, step-by-step mounting instructions, app setup, and troubleshooting tips. By the end, your doorbell will be securely mounted, angled correctly, and ready to keep your home safe.
Let’s get started!
Why Use a Wedge with Your Blink Doorbell?
Visual guide about How to Install Blink Doorbell with Wedge
Image source: i.etsystatic.com
The wedge that comes with your Blink Doorbell isn’t just a plastic accessory—it’s a smart design feature meant to improve your camera’s field of view. Without a wedge, your doorbell might point straight ahead, which can create blind spots below the camera or miss people approaching from the side.
By installing the Blink Doorbell with a wedge, you tilt the device slightly downward. This gives you a better view of the doorstep, packages left on the ground, and people’s faces as they approach. It also helps reduce glare from sunlight and improves motion detection accuracy.
Think of it like adjusting a security camera in a store—you want the lens to see the entrance, not just the ceiling. The wedge helps you achieve that ideal angle without needing extra brackets or DIY hacks.
Tools and Materials You’ll Need
Before you begin, gather these tools and materials to make the installation smooth and safe:
- Blink Doorbell (with wedge included)
- Blink Sync Module (if not already installed)
- Drill with drill bits (for wood, brick, or siding)
- Screwdriver (Phillips head)
- Measuring tape
- Level (to ensure a straight mount)
- Pencil (for marking drill points)
- Wire strippers (if replacing a wired doorbell)
- Electrical tape (for capping wires)
- Optional: Wall anchors (for drywall or brick)
- Optional: Smartphone with Blink app installed
Having everything ready saves time and prevents mid-installation trips to the hardware store.
Step 1: Choose the Right Location
Picking the best spot for your Blink Doorbell is crucial. A poorly placed doorbell can miss visitors, trigger false alarms, or get damaged by weather.
Height Matters
Install your doorbell at a height of 4 to 5 feet from the ground. This is the sweet spot for capturing faces and packages. Too high, and you’ll only see the top of someone’s head. Too low, and it might get bumped or blocked by plants.
Face the Walkway
Point the camera toward the main path people use to approach your door. Avoid aiming it directly at a bright window or the sun, which can cause glare or washed-out video.
Check Wi-Fi Signal
Your Blink Doorbell needs a strong Wi-Fi connection. Use your phone to check signal strength at the installation spot. If it’s weak, consider moving the Sync Module closer or using a Wi-Fi extender.
Avoid Obstructions
Make sure nothing blocks the camera’s view—like a mailbox, plant, or decorative item. Also, keep it away from sprinklers or areas that get heavy rain.
Step 2: Remove the Old Doorbell (If Applicable)
If you’re replacing an existing doorbell, you’ll need to remove it carefully—especially if it’s wired.
Turn Off Power
Safety first! Go to your electrical panel and turn off the power to the doorbell circuit. Use a non-contact voltage tester to confirm the wires are not live.
Unscrew and Disconnect
Remove the old doorbell from the wall. Unscrew the wires and gently pull them out. Don’t cut them—just disconnect and cap each wire with electrical tape. This prevents accidental shocks and keeps them ready if you ever reinstall a wired doorbell.
Patch the Wall (Optional)
If the old mounting hole is larger than the Blink bracket, you can patch it with spackle or use a larger mounting plate. But the Blink wedge and bracket are designed to cover most standard holes.
Step 3: Install the Sync Module (If Not Already Done)
The Blink Sync Module connects your doorbell to your Wi-Fi network. It should be plugged into an indoor outlet near your router or within 100 feet of the doorbell.
Plug It In
Find a nearby outlet and plug in the Sync Module. The light should blink blue, indicating it’s searching for devices.
Pair with the App
Open the Blink app on your phone. Tap “Add Device” and follow the prompts to pair the Sync Module. Once connected, it will show as “Online” in the app.
Test the Connection
Move the Sync Module closer to the doorbell location if the signal is weak. You can always relocate it later.
Step 4: Attach the Wedge to the Mounting Plate
Now it’s time to prepare the mounting hardware.
Identify the Wedge
The wedge is a small plastic piece with a curved or angled surface. It usually snaps onto the back of the mounting plate.
Snap It On
Align the wedge with the mounting plate and press firmly until it clicks into place. Make sure it’s secure—you don’t want it falling off after installation.
Check the Angle
Hold the plate up to the wall to see how the doorbell will tilt. The wedge should angle the camera slightly downward, toward the ground.
Step 5: Mark and Drill Mounting Holes
With the wedge attached, it’s time to mount the plate.
Hold the Plate in Place
Position the mounting plate (with wedge) on the wall at your chosen height. Use a level to make sure it’s straight.
Mark the Screw Holes
Use a pencil to mark where the screw holes will go. The Blink bracket usually has two holes—top and bottom.
Drill Pilot Holes
Drill small pilot holes at the marked spots. This makes it easier to screw in the mounting screws and prevents the wall from cracking.
Insert Wall Anchors (If Needed)
If you’re drilling into drywall, brick, or concrete, use wall anchors for extra support. Tap them gently into the pilot holes with a hammer.
Step 6: Secure the Mounting Plate
Now attach the plate to the wall.
Align and Screw
Hold the mounting plate (with wedge) against the wall, aligning it with the pilot holes. Insert the screws and tighten them with a screwdriver. Don’t over-tighten—this can crack the plastic.
Double-Check the Angle
Use the level again to ensure the plate is straight. The wedge should naturally tilt the doorbell downward.
Test the Fit
Snap the Blink Doorbell onto the plate to make sure it fits securely. It should click into place and stay firm.
Step 7: Install the Blink Doorbell
With the plate mounted, it’s time to attach the doorbell.
Insert the Battery
Open the battery compartment on the back of the doorbell. Insert the included lithium battery, making sure the polarity (+ and –) matches the markings.
Snap It On
Align the doorbell with the mounting plate and press firmly until it clicks. The wedge will now angle the camera correctly.
Secure with Screw (Optional)
For extra security, use the small anti-theft screw provided. Insert it into the bottom of the doorbell and tighten with a screwdriver. This prevents someone from easily removing it.
Step 8: Set Up the Blink App
Your doorbell is mounted—now let’s get it connected.
Open the Blink App
Launch the app on your smartphone. If you haven’t already, create an account or log in.
Add the Doorbell
Tap “Add Device” and select “Doorbell.” The app will search for nearby devices.
Scan the QR Code
Point your phone’s camera at the QR code on the back of the doorbell. The app will recognize it and begin pairing.
Follow the Prompts
The app will guide you through naming the doorbell, selecting your Wi-Fi network, and setting up motion zones. Choose a name like “Front Door” for easy identification.
Test the Connection
Once paired, the app will show a live view. Check the video quality and make sure the angle looks right.
Step 9: Adjust Settings for Best Performance
Now that your doorbell is online, fine-tune the settings.
Motion Zones
In the app, go to “Motion Settings” and draw zones where you want alerts. Exclude areas like busy streets or trees to reduce false alarms.
Sensitivity
Adjust motion sensitivity based on your environment. High sensitivity catches more movement but may trigger on leaves or shadows.
Clip Length
Set how long each recording is—typically 10 to 30 seconds. Longer clips capture more action but use more storage.
Notifications
Enable push notifications so you’re alerted when motion is detected. You can also set quiet hours to avoid nighttime alerts.
Step 10: Test the Doorbell
Before calling it a day, test everything.
Check the Live View
Open the app and tap “Live View.” Make sure the image is clear and the angle covers your doorstep.
Trigger Motion
Walk in front of the doorbell to test motion detection. You should receive a notification and a recording.
Test the Chime
If you have a Blink Mini or Sync Module with a chime, press the doorbell button to hear it ring.
Review Recordings
Go to the “Clips” section in the app to see your test recording. Play it back to check audio and video quality.
Troubleshooting Common Issues
Even with careful installation, you might run into problems. Here’s how to fix the most common ones.
Doorbell Won’t Connect to Wi-Fi
Make sure the Sync Module is within range and plugged in. Restart both the doorbell and Sync Module by removing the battery and unplugging for 10 seconds. Re-pair in the app.
Poor Video Quality
Check for dirt on the lens—wipe it gently with a microfiber cloth. Ensure the camera isn’t pointed at a bright light source.
Short Battery Life
Cold weather drains batteries faster. Replace with high-quality lithium batteries. Reduce motion sensitivity or clip length to save power.
False Motion Alerts
Adjust motion zones to exclude moving trees or cars. Lower sensitivity if needed.
Doorbell Falls Off
Make sure the mounting plate is securely screwed in. Use the anti-theft screw to lock it in place.
Tips for a Professional-Looking Installation
A clean install not only works better—it looks better too.
- Use a level to keep everything straight.
- Hide wires if replacing a wired doorbell (tuck them into the wall).
- Paint the mounting plate to match your wall color for a seamless look.
- Install during daylight for better visibility.
- Ask a friend to help hold the plate while you drill.
Conclusion
Installing a Blink Doorbell with a wedge is a simple upgrade that greatly improves your home security. By following this guide, you’ve learned how to choose the right location, mount the wedge correctly, connect to the app, and troubleshoot common issues.
The wedge ensures your camera sees the right angle—capturing faces, packages, and movement without blind spots. With proper setup, your Blink Doorbell will deliver reliable alerts, clear video, and peace of mind.
Remember to test everything, adjust settings for your environment, and keep the app updated. Your smart doorbell is now ready to protect your home 24/7.
Welcome to smarter security—one wedge at a time.