This guide walks you through the complete process of installing your Aiwit video doorbell, from checking compatibility to final app setup. Whether you’re replacing an old doorbell or installing a new one, we’ll help you get it working smoothly in under an hour.
Key Takeaways
- Check compatibility first: Ensure your existing doorbell wiring and transformer meet Aiwit’s voltage requirements (16–24V AC) to avoid damage or poor performance.
- Turn off power safely: Always shut off the circuit breaker before handling wires to prevent electrical shock or short circuits.
- Use the right tools: A screwdriver, voltage tester, and drill (if needed) make installation faster and safer.
- Download the Aiwit app early: The app guides setup, connects to Wi-Fi, and lets you customize motion zones and alerts.
- Test before final mounting: Power on and test the doorbell temporarily before securing it permanently to catch issues early.
- Optimize Wi-Fi signal: Place the doorbell within range of your router or use a Wi-Fi extender for reliable video streaming.
- Adjust settings post-install: Fine-tune motion sensitivity, night vision, and notification preferences for the best experience.
How to Install Aiwit Video Doorbell: A Complete Step-by-Step Guide
So, you’ve got your hands on an Aiwit video doorbell—congratulations! This smart device brings peace of mind with live video, two-way audio, motion alerts, and night vision. But before you can see who’s at the door from your phone, you need to install it properly.
Don’t worry—this isn’t rocket science. With the right tools, a little patience, and this detailed guide, you’ll have your Aiwit doorbell up and running in under an hour. Whether you’re replacing an old mechanical doorbell or installing one for the first time, we’ve got you covered.
In this guide, you’ll learn:
– How to check if your home is compatible with the Aiwit doorbell
– What tools and materials you’ll need
– Step-by-step wiring and mounting instructions
– How to connect the doorbell to the Aiwit app
– Tips for optimizing performance and avoiding common mistakes
– Troubleshooting solutions for common issues
Let’s get started!
What You’ll Need Before You Begin
Visual guide about How to Install Aiwit Video Doorbell
Image source: aiwit.app
Before you touch a single wire, gather these tools and materials. Having everything ready saves time and frustration.
Tools
- Phillips-head screwdriver
- Flat-head screwdriver (for prying off old plates)
- Voltage tester (non-contact type recommended)
- Drill and drill bits (if mounting on brick, stucco, or concrete)
- Level (to keep the doorbell straight)
- Pencil or marker (for marking drill holes)
Materials
- Aiwit video doorbell (obviously!)
- Mounting bracket (included in the box)
- Screws and wall anchors (also included)
- Wire nuts (usually included, but have extras handy)
- Optional: Wi-Fi extender (if your front door is far from the router)
Safety Gear
- Safety glasses (especially if drilling)
- Work gloves (to protect hands from sharp edges)
Step 1: Check Compatibility
Not every home is ready for a smart doorbell. The Aiwit video doorbell requires a few key things to work properly. Skipping this step could lead to malfunction, no power, or even damage to the device.
Check Your Existing Doorbell Wiring
Most homes with a traditional doorbell have low-voltage wiring running from a transformer to the doorbell button and chime. The Aiwit doorbell needs this wiring to stay powered 24/7.
If you don’t have existing wiring, you’re out of luck—Aiwit does not offer a battery-only model. You’ll need to run new wires or consider a different brand. But if you already have a wired doorbell, you’re in good shape.
Test the Voltage
This is critical. The Aiwit doorbell works best with a transformer that outputs **16 to 24 volts AC**. Too little voltage, and the doorbell won’t charge or function. Too much, and you risk frying the electronics.
Here’s how to test:
1. Turn off the power at the circuit breaker.
2. Remove your old doorbell button.
3. Carefully disconnect the two wires.
4. Turn the power back on.
5. Use a non-contact voltage tester to confirm live wires.
6. Use a multimeter to measure the voltage between the two wires.
If the reading is between 16V and 24V AC, you’re good to go. If it’s below 16V, your transformer may be too weak. If it’s above 24V, you might need a voltage regulator or a new transformer.
Check Your Wi-Fi Signal
The Aiwit doorbell connects to your home Wi-Fi network to send alerts and stream video. A weak signal can cause lag, dropped connections, or failed recordings.
Stand at your front door with your phone and check the Wi-Fi signal strength. If it’s weak (one or two bars), consider:
– Moving your router closer to the front of the house
– Using a Wi-Fi extender or mesh network system
– Upgrading to a stronger router
The Aiwit doorbell supports 2.4 GHz Wi-Fi only—it does not work with 5 GHz networks. Make sure your router broadcasts a 2.4 GHz band.
Step 2: Turn Off the Power
Safety first! Even though doorbell wires carry low voltage, they can still give you a shock—and short circuits can damage your doorbell or chime.
Locate the Circuit Breaker
Find the breaker that controls your doorbell. It’s often labeled “doorbell,” “chime,” or “front door.” If you’re not sure, turn off breakers one by one and test the doorbell until it stops working.
Turn Off the Power
Switch the correct breaker to the “OFF” position. Use a non-contact voltage tester at the doorbell wires to confirm no power is flowing.
Label the Wires (Optional but Helpful)
If your old doorbell has two wires, they’re usually interchangeable. But if you’re nervous, label them with tape (e.g., “Front” and “Trans”) so you remember which goes where.
Step 3: Remove the Old Doorbell
Now it’s time to take off the old button.
Unscrew the Old Button
Use a screwdriver to remove the screws holding the old doorbell in place. Gently pull the button away from the wall.
Disconnect the Wires
Loosen the terminal screws or pull the wires out of the back. Be careful not to let the wires fall back into the wall. If they do, you may need a wire puller or fish tape to retrieve them.
Inspect the Wiring
Check the wires for fraying, corrosion, or damage. If they’re in bad shape, trim the ends and strip about 1/4 inch of insulation to expose fresh copper.
Step 4: Install the Mounting Bracket
The Aiwit doorbell comes with a mounting bracket that holds the device securely. You’ll attach this bracket to the wall first, then snap the doorbell onto it.
Position the Bracket
Hold the bracket against the wall where you want the doorbell. Use a level to make sure it’s straight. Mark the screw holes with a pencil.
Drill Pilot Holes (If Needed)
If you’re mounting on wood, you can screw directly into the wall. For brick, stucco, or concrete, drill pilot holes using a masonry bit. Insert wall anchors for a secure fit.
Secure the Bracket
Line up the bracket with the holes and screw it in place. Make sure it’s tight and level.
Connect the Wires
Feed the two doorbell wires through the center hole of the bracket. Strip about 1/4 inch of insulation if needed.
The Aiwit doorbell doesn’t require polarity, so you can connect the wires to either terminal. Loosen the screws on the bracket’s terminal posts, insert the wires, and tighten the screws.
Pro tip: If the wires are too short, use wire nuts to extend them with spare 18-gauge wire.
Step 5: Attach the Aiwit Doorbell
Now for the fun part—putting the doorbell on the bracket.
Align and Snap
Hold the Aiwit doorbell with the camera facing forward. Align the bottom of the doorbell with the bracket’s lower hook. Then press the top firmly until it clicks into place.
Secure with Security Screw
Use the included security screw and a screwdriver to lock the doorbell to the bracket. This prevents theft—no one can just pull it off the wall.
Step 6: Turn the Power Back On
Head back to the circuit breaker and flip the doorbell breaker to “ON.”
Wait about 30 seconds. You should see the Aiwit doorbell’s LED light up. It may flash blue or white as it boots up.
If nothing happens:
– Double-check that the wires are securely connected
– Confirm the breaker is on
– Test the voltage again
Step 7: Download and Set Up the Aiwit App
The Aiwit app is your control center. It lets you view live video, talk to visitors, adjust settings, and receive alerts.
Download the App
Search for “Aiwit” in the Apple App Store or Google Play Store. Download and install the app.
Create an Account
Open the app and sign up with your email or phone number. Verify your account via the confirmation link or code.
Add Your Doorbell
1. Tap “Add Device” or the “+” icon.
2. Select “Video Doorbell.”
3. Follow the on-screen instructions.
4. When prompted, scan the QR code on the back of your doorbell or enter the serial number manually.
Connect to Wi-Fi
The app will ask you to connect the doorbell to your Wi-Fi network.
– Select your 2.4 GHz network (not 5 GHz).
– Enter your Wi-Fi password carefully.
– Wait while the doorbell connects. This may take 1–2 minutes.
If it fails:
– Move closer to your router
– Restart your router
– Ensure the password is correct
– Try resetting the doorbell (see troubleshooting)
Test the Connection
Once connected, the app should show a live video feed. Tap the microphone icon to test two-way audio. Wave at the camera to trigger motion detection.
Step 8: Adjust Settings for Best Performance
Now that your doorbell is working, customize it to fit your lifestyle.
Set Motion Zones
In the app, go to “Motion Detection” and draw zones where you want alerts (e.g., driveway, sidewalk). Avoid areas like busy streets to reduce false alarms.
Adjust Sensitivity
If you’re getting too many alerts, lower the motion sensitivity. If you’re missing packages, increase it.
Enable Night Vision
The Aiwit doorbell has infrared night vision. Make sure it’s turned on in the settings. Test it at night to ensure clear footage.
Set Notification Preferences
Choose when you want alerts: always, only at night, or during specific hours. You can also enable sound alerts on your phone.
Enable Cloud or Local Storage
Aiwit offers cloud storage (subscription required) or local storage via a microSD card (sold separately). Choose based on your privacy and budget preferences.
Troubleshooting Common Issues
Even with careful installation, problems can happen. Here’s how to fix the most common ones.
Doorbell Won’t Power On
– Check the breaker is on
– Test voltage at the wires
– Ensure wires are tightly connected
– Try swapping the wires (polarity doesn’t matter, but loose connections do)
Wi-Fi Connection Fails
– Confirm you’re using 2.4 GHz Wi-Fi
– Move closer to the router during setup
– Restart the doorbell and router
– Reset the doorbell (hold the reset button for 10 seconds)
Video is Blurry or Laggy
– Check Wi-Fi signal strength
– Reduce video quality in the app (lower resolution = less data)
– Move the router or add a Wi-Fi extender
Motion Alerts Not Working
– Ensure motion detection is enabled
– Adjust sensitivity and zones
– Make sure the camera lens isn’t blocked by dirt or spiderwebs
Two-Way Audio Not Working
– Check microphone and speaker settings in the app
– Ensure your phone’s volume is up
– Test in a quiet environment
Doorbell Rings but No Video
– This could be a Wi-Fi issue—check connection
– Restart the doorbell
– Reinstall the app or update it
Final Tips for Long-Term Success
To keep your Aiwit doorbell running smoothly:
– Clean the lens monthly with a soft, dry cloth
– Check for firmware updates in the app
– Replace the microSD card if using local storage (every 1–2 years)
– Test the doorbell weekly to ensure it’s working
And remember: if you ever sell your home, include the Aiwit doorbell in the sale—it’s a valuable smart home feature that buyers love.
Conclusion
Installing an Aiwit video doorbell is a smart upgrade that enhances your home’s security and convenience. By following this guide, you’ve learned how to check compatibility, safely wire the device, connect it to your Wi-Fi, and customize settings for the best experience.
With live video, motion alerts, and two-way talk, you’ll always know who’s at the door—even when you’re miles away. And if you run into issues, the troubleshooting tips here will help you get back on track fast.
Now go enjoy your new smart doorbell! Whether it’s catching package thieves, greeting guests, or just checking if the mail arrived, your Aiwit doorbell is ready to serve.