How to Install the Wedge Mount for a Ring Doorbell

This guide walks you through how to install the wedge mount for a Ring Doorbell with clear, beginner-friendly steps. You’ll learn how to adjust the viewing angle, secure the mount, and troubleshoot common issues for optimal performance.

Key Takeaways

• Proper angle adjustment: The wedge mount allows you to tilt your Ring Doorbell downward or sideways for better motion detection and video coverage.
• Easy installation process: Most users can complete the installation in under 30 minutes using basic tools like a drill, screwdriver, and level.
• Compatibility matters: Ensure your wedge mount is designed for your specific Ring Doorbell model (e.g., Ring Video Doorbell 2, 3, 4, or Pro).
• Use a level for accuracy: A bubble level helps prevent crooked mounting, which can affect video quality and motion sensing.
• Weatherproofing is essential: Seal screw holes and edges with silicone caulk to protect against rain, snow, and moisture damage.
• Test after installation: Use the Ring app to check the live view and motion zones to confirm the new angle works as intended.
• Troubleshooting tips included: If your doorbell disconnects or the view is obstructed, this guide offers quick fixes.

How to Install the Wedge Mount for a Ring Doorbell

If you’ve ever looked at your Ring Doorbell and thought, “I wish it could see more of my front walkway” or “Why is it only catching people halfway up the steps?”, then you’re not alone. Many Ring users face this issue—the default mounting angle isn’t always ideal for every home layout. That’s where the wedge mount comes in.

The wedge mount is a simple but powerful accessory that lets you adjust the angle of your Ring Doorbell. Whether you need to tilt it down to capture packages left at your door or angle it sideways to monitor a driveway, the wedge mount gives you the flexibility to customize your view. And the best part? Installing it is easier than you might think.

In this guide, we’ll walk you through how to install the wedge mount for a Ring Doorbell—from gathering your tools to testing the final setup. You’ll learn why the wedge mount matters, how to choose the right one, and step-by-step instructions to get it mounted securely and correctly. Whether you’re a DIY newbie or a seasoned home improver, this guide will help you get the most out of your Ring Doorbell.

Why Use a Wedge Mount?

Before we dive into the installation, let’s talk about why the wedge mount is such a valuable upgrade.

By default, Ring Doorbells are designed to mount flat against a wall. But not every home has a straight, vertical surface right next to the door. Maybe your door is set back in a recessed entryway. Maybe your front walk slopes upward, and you want to capture visitors as they approach. Or perhaps you’ve noticed that your motion alerts are triggered too late—because the camera only sees people when they’re already at the door.

The wedge mount solves these problems by allowing you to angle your doorbell. It comes in different degrees—commonly 10°, 20°, and 30°—so you can choose the tilt that best fits your needs. A 10° wedge gives a slight downward angle, perfect for seeing packages or pets. A 30° wedge is great for capturing a wider approach, like a driveway or staircase.

Using a wedge mount also improves motion detection. Ring’s motion sensors rely on visual cues, so if the camera is pointing too high or too low, it might miss activity. With the right angle, you’ll get earlier alerts and fewer false triggers.

Plus, the wedge mount is built to be weather-resistant and durable. It’s made from high-quality plastic that won’t crack or fade in the sun, and it’s designed to fit snugly with your Ring Doorbell model.

In short, the wedge mount isn’t just an accessory—it’s a smart upgrade that enhances your home security.

What You’ll Need

Before you start, make sure you have all the necessary tools and materials. Most of these are common household items, but it’s good to double-check so you don’t have to pause mid-installation.

Here’s your checklist:

• Ring Wedge Mount: Make sure it’s compatible with your Ring Doorbell model. Ring sells official wedge mounts, but third-party options are available—just verify compatibility.
• Power Drill: For drilling pilot holes into the wall or siding.
• Drill Bits: Use a masonry bit if mounting into brick or concrete, or a standard wood bit for siding or wood.
• Screwdriver: A Phillips head screwdriver is usually needed for tightening screws.
• Screws and Wall Anchors: These usually come with the wedge mount kit. Use anchors if mounting into drywall or brick.
• Level: A small bubble level ensures your mount is straight. Crooked mounting can throw off the camera angle.
• Pencil: For marking drill points.
• Measuring Tape: Helps you position the mount at the right height and distance from the door.
• Silicone Caulk (optional but recommended): For sealing around the mount to prevent water damage.
• Safety Gear: Safety glasses and gloves, especially if drilling into hard surfaces.

If you’re replacing an existing Ring Doorbell, you may also need a junction box cover or mounting bracket adapter, depending on your setup. Ring provides these in some kits, or you can purchase them separately.

Step 1: Choose the Right Wedge Mount

Not all wedge mounts are created equal. The first step is making sure you have the correct one for your Ring Doorbell model.

Ring offers official wedge mounts for most of its doorbell models, including:

• Ring Video Doorbell (1st gen)
• Ring Video Doorbell 2
• Ring Video Doorbell 3 and 3 Plus
• Ring Video Doorbell 4
• Ring Video Doorbell Pro and Pro 2

Each model has a slightly different shape and mounting mechanism, so using the wrong wedge mount can lead to a loose fit or installation issues.

When shopping, look for a wedge mount that specifically lists your Ring model as compatible. You can find these on the Ring website, Amazon, or other electronics retailers. Third-party mounts are available, but we recommend sticking with Ring-approved options for the best fit and warranty support.

Also, consider the angle you need:

• 10° Wedge: Slight downward tilt. Good for seeing packages or pets at the door.
• 20° Wedge: Moderate angle. Ideal for most homes with a standard approach.
• 30° Wedge: Steep tilt. Best for capturing long driveways or staircases.

If you’re unsure, start with a 20° wedge—it’s the most versatile. You can always adjust later or try a different angle if needed.

Step 2: Turn Off Power (If Hardwired)

Safety first! If your Ring Doorbell is hardwired to your home’s electrical system, you must turn off the power before removing or adjusting it.

Here’s how:

Locate Your Doorbell Transformer

Most doorbells are powered by a low-voltage transformer, usually located in your basement, garage, or electrical panel. It’s a small box that steps down your home’s 120V power to 16–24V for the doorbell.

Turn Off the Circuit Breaker

Find the breaker that controls the doorbell circuit. It may be labeled “Doorbell,” “Chime,” or something similar. Flip it to the OFF position.

Test the Power

Use a non-contact voltage tester to confirm there’s no power running to the doorbell wires. Touch the tester to the wires—if it beeps or lights up, the power is still on. Double-check your breaker.

Pro Tip: Take a photo of the wiring before disconnecting anything. This makes reinstallation much easier.

If your Ring Doorbell is battery-powered, you can skip this step. Just remove the battery or ensure the device is powered off before handling.

Step 3: Remove the Existing Doorbell (If Applicable)

If you’re replacing a standard doorbell or upgrading from a flat Ring mount, you’ll need to remove it first.

Unscrew the Faceplate

Use a screwdriver to remove the screws holding the doorbell faceplate in place. Gently pull the faceplate away from the wall.

Disconnect the Wires

Carefully disconnect the two wires from the back of the doorbell. They’re usually held in place with small screws or push-in connectors. Don’t let them fall back into the wall—use electrical tape to secure them to the wall or a nearby surface.

Remove the Old Mounting Bracket

Unscrew the mounting bracket from the wall. If it’s attached with anchors, you may need to wiggle it loose or drill out the screws.

Clean the Area

Wipe down the wall surface to remove dust, dirt, or old adhesive. A clean surface ensures better adhesion for the new mount.

Step 4: Position the Wedge Mount

Now it’s time to figure out where to place the wedge mount.

Determine the Ideal Height

Ring recommends mounting your doorbell between 48 and 60 inches (4 to 5 feet) from the ground. This height captures most visitors’ faces and avoids tampering.

Use a measuring tape to mark the center point at your desired height.

Consider the Angle

Think about what you want the camera to see. If your walkway slopes up, angle the wedge downward. If your door is recessed, angle it outward.

Hold the wedge mount against the wall in the desired position. Use a level to make sure it’s straight—not tilted left or right.

Mark the Screw Holes

Once you’re happy with the position, use a pencil to mark the locations of the screw holes through the wedge mount’s base.

Pro Tip: If you’re mounting into brick or concrete, use a masonry bit to drill pilot holes. This prevents cracking and makes screwing easier.

Step 5: Drill Pilot Holes

Drilling pilot holes ensures a clean, secure installation.

Select the Right Drill Bit

• For wood or siding: Use a standard drill bit slightly smaller than your screw diameter.
• For brick, concrete, or stucco: Use a masonry bit. A hammer drill works best for hard surfaces.

Drill Carefully

Drill straight into the wall at each marked point. Go slowly to avoid cracking the material. For masonry, use a hammer drill setting if available.

Insert Wall Anchors (If Needed)

If you’re mounting into drywall, brick, or concrete, insert wall anchors into the pilot holes. Tap them gently with a hammer until flush.

Pro Tip: Blow out the holes with compressed air or a straw to remove dust. This helps the anchors sit properly.

Step 6: Attach the Wedge Mount

Now it’s time to secure the wedge mount to the wall.

Align the Mount

Hold the wedge mount against the wall, aligning the screw holes with the pilot holes or anchors.

Insert and Tighten Screws

Use your screwdriver or drill to insert the screws. Tighten them until the mount is snug, but don’t over-tighten—this can crack the plastic or damage the wall.

Check the Level

Use your bubble level again to confirm the mount is straight. Adjust if necessary.

Pro Tip: If the mount feels loose, double-check that the anchors are fully seated. You may need longer screws or larger anchors.

Step 7: Reconnect the Wedge Mount to the Doorbell

With the wedge mount securely in place, it’s time to attach your Ring Doorbell.

Attach the Doorbell to the Wedge

Most Ring wedge mounts use the same mounting system as the standard bracket. Simply slide the doorbell onto the wedge mount until it clicks into place.

Secure with Screws (If Applicable)

Some models require a security screw to prevent theft. Use the included screw and a screwdriver to fasten the doorbell to the mount.

Reconnect the Wires (If Hardwired)

If your doorbell is hardwired, reconnect the two wires to the terminals on the back of the doorbell. Tighten the screws to secure them.

Replace the Faceplate

Snap or screw the faceplate back into place.

Step 8: Restore Power and Test

Now that everything is installed, it’s time to power up and test.

Turn the Power Back On

Go to your circuit breaker and flip the doorbell breaker back to ON.

Wait for the Doorbell to Boot

It may take 30–60 seconds for the Ring Doorbell to reconnect to Wi-Fi and power up.

Open the Ring App

Launch the Ring app on your phone. You should see your doorbell come online.

Check the Live View

Tap the doorbell to open the live feed. Look at the angle—does it show what you expected? Can you see the walkway, driveway, or package area?

Adjust Motion Zones (If Needed)

In the Ring app, go to Device Settings > Motion Settings > Motion Zones. Draw zones to focus on areas you want to monitor and ignore others (like busy streets).

Test Motion Detection

Walk in front of the doorbell to trigger a motion alert. Check if it detects you early and sends a notification.

Step 9: Weatherproof the Installation

To protect your investment, it’s important to seal the installation against the elements.

Apply Silicone Caulk

Run a thin bead of clear silicone caulk around the edges of the wedge mount where it meets the wall. This prevents water from seeping behind the mount.

Seal Screw Heads

Cover the screw heads with a small dab of caulk to prevent rust and water entry.

Check for Gaps

Make sure there are no gaps between the mount and the wall. Fill any with caulk.

Pro Tip: Use a caulk that’s paintable if you plan to touch up the wall later.

Troubleshooting Common Issues

Even with careful installation, you might run into a few hiccups. Here’s how to fix them.

Doorbell Won’t Power On

• Check that the breaker is on.
• Verify the wires are securely connected.
• Ensure the battery is charged (if battery-powered).

Live View Is Crooked

• Use the level to check the wedge mount.
• Loosen the screws slightly, adjust, and retighten.
• Some Ring models have a digital level in the app—use it to fine-tune.

Motion Alerts Are Too Late

• The angle may be too steep or shallow.
• Adjust the wedge mount or try a different angle.
• Reposition motion zones in the app.

Wi-Fi Connection Drops

• The new angle might be farther from your router.
• Consider a Wi-Fi extender or Ring Chime Pro for better signal.

Water Seeping Behind the Mount

• Reapply silicone caulk.
• Ensure the mount is flush against the wall.

Final Tips for Success

• Take your time: Rushing can lead to mistakes. A proper installation takes 20–30 minutes.
• Use the app: The Ring app has tools like the digital level and motion zone editor—use them!
• Ask for help: If you’re drilling into brick or unsure about wiring, consult a professional.
• Keep the packaging: Save the box and instructions in case you need to return or replace the mount.

Conclusion

Installing the wedge mount for your Ring Doorbell is a simple upgrade that can make a big difference in your home security. By adjusting the angle, you improve visibility, motion detection, and overall performance. With the right tools, a little patience, and this step-by-step guide, you can complete the installation in under an hour.

Remember to choose the right wedge for your model, use a level for accuracy, and weatherproof the installation to protect against the elements. Once everything is set up, test the live view and motion alerts to ensure everything works as expected.

Whether you’re capturing packages, monitoring a driveway, or just want better coverage, the wedge mount helps your Ring Doorbell do its job better. So grab your tools, follow these steps, and enjoy a smarter, safer front door.